11/13/2022 0 Comments Franke orx 610may elect to epoxy in the screws or use brass anchors.ģ. Pre-drill holes for brackets based on best practices for countertop material. This template has been designed to achieve either installation noted below.Ģ. Inspect sink carefully before installation.ġ. This sink is specifically designed to be undermounted in either solid surface or granite countertops.ĬAUTION: Sink edge may be sharp handle with caution. UNDERMOUNT SINK TEMPLATE INSTALLATION INSTRUCTIONS Please use the template included in your Franke sink (if applicable). Apply a bead of silicone evenly along wedge of underside of counter.ī. NOTE: You the fabricator may elect to epoxy in the screw or use a brass anchor (not provided).ī. Pre-drill holes according to method desired based on countertop material. Determine placement of clip brackets as indicated by template. Cut-out should be flush with the countertop.ī. Tighten the clip against the underside of the counter. (Waste hole should be positioned at the rear). Lower the sink into the countertop cutout. simply remove the outer ring at the perforated score.ĬAUTION: Damage caused by improper handling or installation is not covered by the warranty. The template is standard for inset mounting. NOTE: The sink template has been designed for both inset and undermounting. SINKS THAT CAN EITHER BE INSET or UNDERMOUNTED may elect to epoxy in the screw or use a brass anchor. Determine placement of the clip brackets as indicated on the template. FRANKE is not responsible for an improperly cut countertop or improper installation.Ģ. The actual sink and accessories should ALWAYS be present to ensure a perfect cut. dxf file downloaded from website) is only a guide. UNDERMOUNT: STAINLESS STEEL: MULTIPLE BOWLS FRANKE is not responsible for an improperly cut countertop or improper installation. NOTE: The template included (or dxf file downloaded from website) is only a guide. tighten clip brackets against the sink edge. Position and align sink over the opening. Apply a bead of silicone evenly along edge on the underside of countertop.Ĥ. NOTE: You the fabricator may elect to epoxy in the screw or use a brass anchor.ģ. The size should be exact as this sink uses coordinating accessories which fit precisely in the cut out.Ģ. This sink is specifically designed to be undermounted in a solid surface countertop only.ĬAUTION: Sink edge may be sharp handle with caution. Inset A Inset B Inset C UNDERMOUNT: STAINLESS STEEL: SINGLE BOWL Installation Instructions for Your Franke Stainless Steel Sink Find your sink model listed on the back page for corresponding method of installation. Please visit our website for separate Fireclay sink installation instructions. NOTE: none of these installations apply to Franke Fireclay Sinks. Clips will automatically adhere to the counter making certain drain hole is to the back. Place silicone on inner edge of cut-out and a thin application along cut line atop the counter.ĥ. Strainer basket may be assembled at this time if desired.Ĥ. Cut along the outline (NOTE: it is important to cut exactly to the trace line – the sink ledge that overhangs on the countertopģ. Turn clips out and tighten against the underside of the countertop. If there is no factory installed sealant. Most Franke sinks are shipped with factory applied polyseal. Faucet and strainer basket may be assembled at this time. NOTE: Some clips may already be in place.Ĥ. (To clear countertop while lowering sink into cutout). Place template on the counter and trace.ģ. File a claim against the shipping agent.ġ. #Franke orx 610 install#NOTE: Inspect sink for damage do not install a damaged unit. UNDERMOUNT: STAINLESS STEEL: SINGLE BOWL. #Franke orx 610 manual#Franke LAX11014 15 Inch Undermount Single Bowl Stainless Ste - Use Manual - Use Guide PDF.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |